Skip to content
A black knee-high compression sock on a leg form, seen from the side and from the frontAccessAble · family brandStandard compression

Private Label & OEM · Rainsville, Alabama

Compression Socks

Graduated compression sock manufacturing for private label and OEM programs, knit in Rainsville, Alabama, with yarn origin confirmed per program.

This page covers Runway Knitting's compression programs, knit in Rainsville, Alabama. It is written for private label and OEM buyers who need a compression profile specified across a size run rather than a catalog product. Program tracks, materials, specifications, and the documentation approach are set out below.

Photographed: AccessAble. A family-owned compression sock brand, knit at Runway Knitting. accessablecompression.com

A machine with a row of blue tension units, white and blue yarn packages, and safety signs on its side panel
Yarn running through a row of tension units

Overview

Intended applications

  • Recovery and athletic brands
  • Medical-device programs
  • Travel and everyday wellness brands
  • Workwear

Compression is a knit outcome, not an add-on: yarn selection, machine setup, and finishing all decide how a sock holds a gradient across the leg and how it behaves after repeated wear and wash. We develop compression constructions against your target profile and your sizing system, and compression is measured in-house on finished socks and verified by third-party testing. The same sizing logic carries over to our arm and leg sleeve programs when a brand runs both articles together. Programs are private label and OEM only.

Options

Compression program tracks

A black knee-high compression sock on a leg form, seen from the sideAccessAble · family brandStandard compression

Standard Compression Programs

Recovery, athletic, travel, everyday wellness, and workwear programs. Construction is developed against your target profile and sizing system, sampled, and locked as a written spec before production.

6 options · swipe

01

Graduated compression zones

Compression distributed along the leg so the gradient follows the profile defined for your program rather than a stock setting.

02

Compression level knit to spec

Machine setup and yarn tension are developed against your target level and verified on sample before the spec is locked.

03

Foot and calf sizing systems

Sizing built on foot length and calf circumference.

04

Toe and heel options

Closed toe, open toe, and heel construction selected for the wearer and the way the product is put on.

05

Cuff and top band

Top band tension specified to hold position.

06

Branding

Knitted-in logos, cuff treatments, and size or side indicators developed with your artwork.

A pair of white knee-high support stockings on leg forms, seen from the side and from the frontSample image

Medical-Device Compression Programs

Runway Knitting is an FDA-registered medical device establishment with a device listing for medical support stockings under product code DWL, Class II, 21 CFR 880.5780(a). Registration and listing do not mean FDA has approved the establishment or approved or cleared a product. The applicable requirements and each party’s responsibilities must be identified before a medical-device program proceeds.

6 options · swipe

01

Profile specified per size

The gradient is specified per size. Compression is measured in-house on finished socks and verified by third-party testing.

02

Measurement-based sizing

Sizing built on stated limb measurements and finished dimensions.

03

Documented knit spec

Yarn system, gauge, machine setup, and finished dimensions recorded as one program record before production begins.

04

Traceability handling

Documentation and traceability requirements are identified at program start.

05

Toe, heel, and band construction

Closed or open toe, heel placement, and band tension specified for wearers who put the product on and take it off frequently.

06

Requirements identified up front

Applicable documentation and inspection requirements, and responsibility for each, are identified before sampling.

Cones of grey, yellow and black yarn hanging from overhead racksRows of black yarn on a green machine frame
Yarn cones on the overhead racks that feed the knitting machines · Rows of black yarn on a yarn machine

Materials

Materials & functional choices

Compression depends on recovery, so elastic content and yarn construction are specified together with the target profile.

Spandex and elastane content
Elastic content and feed method selected to deliver the target profile.
Nylon and poly blends
Face yarns chosen for durability, hand, and how the fabric recovers after stretch.
Moisture behavior
Yarn systems selected for wear duration: long-haul travel and full-shift workwear behave differently than post-training recovery.
Finishing
Boarding and finishing set the finished dimensions that the compression profile is measured against.
A row of knitting machines with blue control panels, with cones of yarn hanging overhead
Knitting machines, fed from yarn cones overhead

Process

Manufacturing process for this product

  1. Feasibility

    We review the target profile, sizing system, and end use against our compression capability.

  2. Yarn and gauge

    Elastic system, face yarn, and gauge are selected for the profile you need.

  3. Knit development

    Gradient zones, toe, heel, and top band are specified and knit as a body.

  4. Sampling

    Samples are produced and measured so the profile can be evaluated on the finished sock.

  5. Approval

    Knit spec, finished dimensions, documentation, and packaging are locked with your team.

  6. Production

    The approved spec runs on the knitting floor, where its samples were knit.

Specifications

Typical program parameters

Figures are program-specific and depend on construction, yarn availability, and packaging. Confirmed lead times and sample timing are published here once finalized.

Compression Socks: program specifications

Compression Socks: program specifications
ParameterDetail
Customization surfacesKnit-in logos, top band branding, and colorwork from your artwork; packaging, labeling, and documentation formats specified per program.
SizingMeasurement-based sizing systems, developed and sampled across the size run before approval.
Minimum orderSet per program during development; depends on construction, size run, colorways, yarn and price
Development samples and production lead timePublished after program review.
Program typesPrivate Label & OEM
Primary inputs neededEnd use, target compression profile, size run and measurement system, yarn preferences, documentation requirements, packaging requirements
Compression testingMeasured in-house on finished socks and verified by third-party testing
Origin statusKnit in Rainsville, Alabama; yarn origin confirmed in writing per program

Sampling & development pathway

Development & quality

Cones of pink yarn with purple, teal and white cores in a cardboard bin

Pink yarn on cones, in a bin on the mill floor

  1. Program review

    We start from the intended use and whether the program is standard or medical-device, because that decides how development is documented.

  2. Spec definition

    Compression profile, sizing system, and finished measurements are agreed with you before production.

  3. Sample rounds

    Samples are produced for fit, hand, and profile evaluation. Revision rounds depend on how far the first sample sits from intent.

  4. Wear and wash review

    You evaluate recovery and fit retention under your own conditions before the spec is approved.

  5. Approval and handoff

    The approved sample becomes the reference for production and every replenishment run afterward.

  • Finished dimensions verified against the approved sample across the size run.
  • Compression measured in-house on finished socks and verified by third-party testing.
  • Stitch consistency checked against the approved sample.
  • Toe closure and top band condition inspected.
  • Color and artwork placement compared to the approved reference.
  • Documentation defined for the program is kept with the program record.

FAQs

Compression Socks questions

Compression socks sold in the United States come from a mix of overseas suppliers and a smaller group of domestic knitters, and Runway Knitting Inc. is one of the domestic ones. We knit in Rainsville, Alabama, with 33 years in business behind the operation, and every compression program we run is private label or OEM; the product ships under your brand, not ours, and we do not sell to consumers. Yarn origin on our compression work depends on the program and is confirmed in writing for each one. We run both standard compression programs for recovery, athletic, travel, and workwear brands and medical-device programs where documentation and traceability requirements are identified at program start. If you are evaluating US compression sock manufacturers, send your target profile, size run, and end use through an RFQ and we will review technical fit first.

We manufacture compression socks for private label and OEM programs, developed to your specification. The starting point is your intended use, target compression profile, sizing system, and any documentation requirements the program carries. From there we select the elastic system, face yarn, and gauge, specify the gradient zones along with toe, heel, and top band construction, and knit samples so the profile can be measured on finished product instead of assumed from a machine setting. You evaluate fit, hand, and recovery under your own wear and wash conditions. Sample rounds and acceptance criteria are agreed before development. Once you approve, the knit spec, finished dimensions, packaging, and branding are locked as one program record, and production runs on the knitting floor, where the samples were knit. Branding can be knitted in, including logos, cuff treatments, and size or side indicators.

We develop compression to a target profile rather than selling from a fixed level chart, and the achievable range depends on the yarn system, the gauge, and the sizing your program uses. We do not publish mmHg ranges here because the figure that matters is the one measured on your finished construction after boarding and finishing, not a generic band copied from a catalog. In development we select the elastic system and face yarn against your target, knit samples, and measure finished dimensions across the size run so you can see how the gradient behaves at each size rather than only in the sample size. If the first sample sits away from your intent, we adjust the elastic feed, tension, or gauge and sample again. Bring your target profile and sizing system into an RFQ and we will confirm what we can hold. Confirmed values publish after program review.

Medical-device requirements depend on the product’s intended use, claims, design, and applicable classification. They can affect development, testing, manufacturing, labeling, records, and responsibilities after sale. A description such as athletic, travel, or everyday does not by itself establish regulatory status. Include the intended use, proposed claims, and any known regulatory requirements in your RFQ so the requirements and each party’s responsibilities can be reviewed.

Minimums are set per program during development and depend on the construction, size run, colorways, yarn and price; ask for them in the RFQ. Technical review confirms construction, packaging format, documentation requirements, and the replenishment pattern. Send your target profile and size run through an RFQ.

A matching request starts with a feasibility review of the physical sample and the required specifications. We measure the construction, identify the yarn system and gauge, and tell you what we can reproduce on our equipment and where a difference is likely, because some elements of another factory's setup do not transfer exactly to ours. We are direct about that before you commit rather than after sampling. Matching work then runs through the same path as new development: spec definition, sampling, wear and wash evaluation under your conditions, and approval against a written record. Bring the size run and any documentation requirements with the sample, since a match on the medium alone is not a match on the program. If a specific element cannot be reproduced, we tell you what the closest achievable construction is so you can decide before development starts.

Compression constructions are built around an elastic system, spandex or elastane, combined with a face yarn such as nylon, poly, or a cotton blend depending on hand and wear duration. The face yarn is chosen for durability, hand, and how it behaves against the skin over a long wear; the elastic system is chosen for the profile and for how well it recovers over repeat wash cycles, since a construction that measures correctly new and loses recovery after laundering has not met the spec. Wear duration matters to the choice: a long-haul travel program and a full-shift workwear program place different demands on moisture behavior than a post-training recovery sock. Yarn availability is confirmed at program review, because some yarns sit on longer supply cycles than others.
Two rows of knitting machines along an aisle, with cones of yarn hanging overhead

Request for quotation

Start a compression socks program.

Send the end use, target construction, size run, and artwork. We review feasibility first and come back with the parameters that apply to your program.

Start an RFQ

Pre-set to Compression Socks · Private label and OEM only